|
New Products
1 M*Ankor NFDS Activator: Nickel coating at rinsing level decreases the activation.
Ankor NFDS activator, increases activation of Nickel so that it would level chrome plating and it would prevent White washing.
***
1**Ankor NFDS is an activation process for use between bright nickel and bright chrome deposits. Milky chrome deposits, patchy and/or cloudy deposits- (white washing) will in this manner be affectively avoided.
**Ankor NFDS replaces the usual chemicals activation in chromic acid. In spite of the very low current densities which are used, Ankor NFDS prevents faults, which would otherwise occur as a result of passivation of the bright nickel deposits (e.g. such as caused by insufficient rising, intervals, which are too long between the nickel and the chrome plating.
*
2 M*Ankor SRK Wetting Agent a poor foaming wetting agent for Bright, Black and Hard Chrome electrolyte causes reduction of the surface tension and reduction of drag - out of electrolyte.
***
2**Ankor SRK Wetting Agent the poor foaming wetting agent Ankor SRK is applied to prevent
spray formation during the electrolysis of chrome solutions.
By reduction of the surface tension, the drag-out losses are evidently reduced. At the usual conditions, the wetting agent is chemically constant and does not virtually influence the physical and corrosive properties of the chrome deposits.
Wetting Agent Ankor SRK is a high viscous concentrate. Before addition into the chrome electrolyte it must be diluted fivefold with distilled water.
*
3 M* Ankor RDK Bright Chrome for increasing throwing power and increases chrome plating of hollows.
*
4 M* Ni- Purifier ZK in Nickel Electrolyte
Copper and Zinc Contamination in Nickel electrolyte causes the coating become tarnished and black. Ni- Purifier ZK removes the contamination, improves the coating and decreases the expenses.
5 M* Entek water displacing liquid for fast drying on metals
One of the problems usually occurs during electroplating is water spots which appears after final rinsing. Entek sheds the water spots from the surface of all metals and makes the drying process faster.
*
6*M F990 Additive
Removes the Iron contaminations in Bright Nickel electrolyte so that No more roughness exists in coating
**
7 **Permapass Immunox 3K Trivalent Blue Passivate
This trivalent chromium-based process provides a blue passivate film on Zinc deposits from all Zinc plating processes and can be used in rack and barrel installations. The process is intended to be both decorative and functional, and providing outstanding corrosion protection superior to conventional blue chromate.
8*M Enseal 37, Sealant (96 - 192 hours) corrosion retarding (WR)
**
9** Topstar TR Bright Nickel Process for Barrel Plating
The Topstar TR process is specially for barrel plating. Its exceptionally good characteristics are the good plating results achievable over a wide current, range, its insensibility against interruptions of the electric current supply, as well as the bright deposits obtainable.
With this electrolyte it is possible to obtain extremely bright, well levelled deposits even at low current densities.
10** Actane KT Activation salt containing Fluoride
Actane KT is a salt containing fluoride, which reacts acidic in aqueous solutions, and is used for making -up activating solutions Copper, Copper Alloys, Zinc die-casts, and steel.
It has proved itself especially useful for brass articles containing lead or such, which have been soldered.
11** Actane K Liquid additive for mineral acid etches
Actane K is Liquid Additive for Mineral Acid Etches. Actane K contains inhibitors which prevent any attack on active metallic surfaces, thereby enabling oxide and scale to be mainly removed. The acid-proof active cleaning substances provide the etch solution with a simultaneous degreasing effect.
With the exception of Nitric Acid, Actane K can be used in all other mineral acids for the etching of iron, steel and colored metals. However colored metals and steel parts are not to be treated together in the same solution.
|